punkisbetter 0 Report post Posted August 16, 2009 io e mio babbo ci siamo messi in testa di provare a costruire un telaio in acciaio. io sono più adetto alla parte "progettuale" (sono un disegnatore tecnico) lui alla parte "costruttiva" (ha un officina meccanico-carpenteria). insomma io da un lato lui dall'altro abbiamo bisogno del vostro aiuto con il maggior numero di link, dritte, guide on-line ecc ecc che ci potete dare! vi ringrazio in anticipo! davide. ;) Share this post Link to post Share on other sites
TONEFIX 38 Report post Posted August 17, 2009 La vedo dura. Senza dime verrà tutto storto. TONEFIX Share this post Link to post Share on other sites
punkisbetter 0 Report post Posted August 17, 2009 pensavamo infatti di fare una dima fissa...giusta per il telaio della mia misura. Share this post Link to post Share on other sites
FixKin 760 Report post Posted August 18, 2009 ciao, di manuali per costruire telai penso non se ne trovino.Ci sono alcuni video che ti possono aiutare tipo questo . Che tipo di saldature volevi fare? Per i tubi la Columbus non vende per piccole quantita' quindi dovrai rivolgerti ad artigiani tipo Vetta, fratelli Bonetti o altri. Stefano Share this post Link to post Share on other sites
lafattaturchina 760 Report post Posted August 18, 2009 http://www.littlefishbicycles.com/frame/beginning.html magari ti può essere utile :) Share this post Link to post Share on other sites
punkisbetter 0 Report post Posted August 18, 2009 per saldature e tubi se ne occupa mio babbo che con l'officina bene o male trova quello che vuole all'ingrosso. pensavamo di acquistare solo il tubo filettato per il movimento centrale e i forcellini. se saldare i punti d'unione tra i tubi viene esteticamente una merda prenderò anche le giunzioni tra i tubi...ma mi piacciono i telai senza. grazie per il video e per il link...entrambi molto utili! Share this post Link to post Share on other sites
loasca 6 Report post Posted September 1, 2009 Ho trovato questo: http://bhovey.com/Masi/Scans/Talbot/index.htm#1 è in inglese e, anche se non l'ho ancora letto, sembra valido. Share this post Link to post Share on other sites
Lanerossi 589 Report post Posted September 1, 2009 Mettere in squadra non lo vedo un problema, uno che fa il meccanico da anni è capace di farti una struttura diritta. I problemi a mio parere stanno in: -recuperare i tubi (vabbè, è il problema minore) -assemblarli in maniera che il progetto del telaio abbia un comportamento dinamico ineccepibile -eseguire saldature di qualità su spessori (inferiori al mm) con cui i saldatori di solito non hanno confidenza e, pur molto bravi, posso commettere errori che il telaio poi non perdona Il grande telaista non era/è solo chi sa fare bene le saldature, ma anche chi sa progettare il telaio in maniera che poi in corsa (discesa, curva, pianura, rilanci, partenze, scatti) si comporti sempre al meglio. Se riuscite in questo punto, be', mettetevi nel mercato! Share this post Link to post Share on other sites
smalltownvideo 185 Report post Posted February 17, 2010 ci siete riusciti a fa sto telaio o no?! Share this post Link to post Share on other sites
Gemasis85 19 Report post Posted February 17, 2010 Ciao, prova a vedere se ti può servire http://www.bikeforest.com/ Se ci rieci fammi sapere. Ciao Share this post Link to post Share on other sites